Digiplex DGP-641 Installationshandbuch PDF herunterladen (Seite 48)

44 Reference & Installation Manual

15 WinLoad Software

The Winload software is not verified by UL.

15.1 Answering Machine Override

SECTION [441]

When using WinLoad to communicate remotely with an installation site

that uses an answering machine or service, the Answering Machine

Override must be programmed. Using WinLoad, call the installation

site and on the second ring press the

[ENTER]

key on the keyboard to

hang up or hang up manually. After hanging up, WinLoad will

immediately call the installation site back or call the site back manually.

The value (00 to 15 X 4 seconds) programmed in section

[441]

represents the delay period the control panel will wait between the first

and second call. If the installation site is called back within the

programmed delay period, the control panel will override the answering

machine or service by picking-up the line on the first ring. To disable

this option program 00 in section

[441]

. Also, see section 15.2.

Example: A security installation is using an answering machine set

to answer after three rings and section [441] has been

programmed with 10 (10 x 4 = 40 seconds). When you call the

installation site with WinLoad the first time, wait two rings and press

[

ENTER] on the keyboard. WinLoad will immediately call the

installation site back. If the second call is made within 40 seconds,

the control panel will pick-up the line on the first ring. If it takes

more than 40 seconds, the control panel will not answer on the first

ring and the answering machine will answer after three rings.

15.2 Ring Counter

SECTION [442]

The value (01 to 15, 00 = disabled) programmed in section [442]

represents the number of rings the control panel will wait before

picking-up the line. If the line is not answered after the number of

programmed rings, the control panel will answer the call. The control

panel resets the Ring Counter every 10 seconds. Therefore, if there

is more than 10 seconds between each ring, the control panel will

reset the counter on the next call. Also, see section 15.1.

15.3 Panel Identifier

SECTION [555]

This four-digit code identifies the control panel to WinLoad before

initiating upload or download. The control panel will verify if the

panel identifier in WinLoad is the same. If the codes do not match,

the control panel will not establish communication. Therefore,

program the same Panel Identifier into both the Digiplex Control

Panel and WinLoad. To program the Panel Identifier, key in the

desired 4-digit hexadecimal number into section [555].

15.4 PC Password

SECTION [556]

This four-digit password identifies the computer running the WinLoad

software to the panel before beginning the download process.

Program the same PC Password into both the Digiplex control panel

and WinLoad. If the passwords do not match, WinLoad will not

establish communication. To program the PC Password, enter the

desired four-digit hexadecimal number into section [556].

15.5 PC Telephone Number

SECTION [560]

The control panel will dial this number when trying to initiate

communication with a computer using WinLoad. You can enter any

digit from 0 to 9 and any special keys or functions (see Table 10,

Special Telephone Number Keys, on page 27) up to a maximum of

32 digits into section [560].

For North American installations using either SIA or

Contact ID reporting formats (see section 8.5 on page

27), enter *70 and then either P (4-second pause) or W

(wait for second dial tone) before the phone number to

disable call-waiting.

15.6 Call WinLoad

Dial the PC Telephone Number programmed in section [560] in

order to communicate with WinLoad. The control panel and

WinLoad will verify that the Panel Identifier and the PC Password

match before establishing communication.

For LCD keypads: press and hold the [0] key, enter the [

INSTALLER

CODE] and then press [FORCE].

For Grafica keypads: press and hold the [0] key, enter the

[INSTALLER CODE], press the center action key (Options), highlight

Call Winload and then press the left action key (Select).

15.7 Answer WinLoad

To perform on-site upload/downloading, connect your computer

directly to the control panel using an ADP-1 line adapter. In

WinLoad set Dialing Condition to Blind Dial. Program the panel

telephone number in WinLoad and follow the ADP-1 Adapter‘s

instructions. When the computer has dialed...

For LCD keypads: press and hold the [0] key, enter the [

INSTALLER

CODE] and press [ARM] to manually answer WinLoad from the

panel. Press [DISARM] to hang up.

For Grafica keypads: press and hold the [0] key, enter the

[INSTALLER CODE], press the center action key (Options), highlight

Answer Winload and then press the left action key (Select). To

hang up, highlight Cancel Communication and then press the left

action key (Select).

15.8 Event Buffer Transmission

SECTION [522]: OPTION [2]

If the Event Buffer contains 974 events since the last upload, the

control panel will make two attempts to establish communication

with a computer using WinLoad by calling the PC Telephone

Number programmed in section [560]. WinLoad must be in Wait To

Dial mode. When the system establishes communication, it will

upload the contents of the Event Buffer to WinLoad. If

communication is interrupted before completing transmission or if

after two attempts, communication is not established, the system

will wait until the Event Buffer attains another 974 events before

attempting to re-communicate with the monitoring station. When

the Event Buffer is full, each subsequent new event will erase the

oldest event in the buffer. The Event Buffer can hold 1024 Events.

1 2 ... 43 44 45 46 47 48 49 50 51 52 53 ... 67 68

Kommentare zu diesen Handbüchern

Keine Kommentare

Digiplex DGP-641 Installationshandbuch Seite 48

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Digiplex DGP-641