Digiplex DGP-641 Installationshandbuch PDF herunterladen (Seite 44)

40 Reference & Installation Manual

Access Control features. This can be used to

disable a lost or stolen card without deleting the

user access code.

13.7.4 Disarm with Access Card

SECTIONS [802] TO [896]: ACCESS OPTION SCREEN, OPTION [2]

When the partition assigned to an Access Door (see section 14.4

on page 41) is armed, it can be disarmed and unlocked upon

presentation of a valid Access Card to the reader. For an Access

Card to be valid, it must be presented during its assigned

Schedule, within its assigned Access Level and be assigned to the

access control module’s assigned partitions depending on the Door

Access Mode (see section 14.5 on page 41). Codes assigned with

the “Arm Only” User Option will not be able to disarm with the card.

Option [2] ON = The Access Card can disarm partitions.

Option [2] OFF = The Access Card cannot disarm partitions.

13.7.5 Card with Extended Unlocked Period

SECTIONS [802] TO [896]: ACCESS OPTION SCREEN, OPTION [3]

Each Access Control Module is programmed with a Door Unlocked

Period and a Door Unlocked Period Extension. The Door Unlocked

Period is the time the door can remain unlatched after access is

granted or after a Request for Exit is received. The Door Unlocked

Period Extension is the amount of time added to the Door

Unlocked Period. For more details refer to the appropriate Digiplex

Module Reference & Installation Manual.

When Card with Extended Unlocked Period is enabled, the two

time periods are added together to allow extra time for the user to

open the Access Door, which may be useful for seniors and for the

physically challenged. Access is only granted during the card's

assigned Schedule and to doors programmed in its Access Level.

Option [3] ON = Extended Unlocked Period is enabled on card

Option [3] OFF = Extended Unlocked Period is disabled on card

Example:

13.7.6 Arming with Access Card

SECTIONS [802] TO [896]: ACCESS OPTION SCREEN, OPTIONS [4],

[5], [6], AND [7]

An Access Card can be programmed to arm the partition(s)

assigned to the door when the valid card is presented to the reader

twice within approximately 5 seconds while the door remains

closed. For an Access Card to be valid, it must be presented during

its assigned Schedule, within its assigned Access Level and be

assigned to the keypad’s assigned partitions depending on the

Door Access Mode (see section 14.5 on page 41). The arming

method is determined by turning ON or OFF one of the options

from [5] to [7].

No Arming with Card

Option [4] OFF = Arming with Access Card is disabled.

Regular Arming with Card

Option [4] ON and Options [5], [6], & [7] OFF = The Access Card

can Regular arm partitions (see section 16.1 on page 45).

Stay Arming with Card

Options [4] and [5] ON and Options [6] and [7] OFF = The Access

Card can Stay arm the partitions (see section 16.1 on page 45).

Instant Arming with Card

Options [4] and [6] ON and Options [5] and [7] OFF = The Access

Card can Instant arm the partitions (see section 16.1 on page 45).

Force Arming with Card

Options [4] and [7] ON and Options [5] and [6] OFF = The Access

Card can Force arm the partitions (see section 16.1 on page 45).

13.7.7 Access to Armed Access Doors

SECTIONS [802] TO [896]: ACCESS OPTION SCREEN, OPTION [8]

An Access Door can be assigned to a zone in Digiplex so it can be

protected by the security system as well (see section 14.4 on page

41). When a valid Access Card with this feature enabled is

presented to an armed door, access will be granted and the Entry

Delay will begin. When this option is enabled, extra security is

provided since a user must enter a user access code to disarm the

area. Access is only granted during the card's assigned Schedule

and to doors programmed in its Access Level. For user access

codes assigned with the “Arm Only” User Option, option [8] should

remain off since they cannot disarm the partition(s).

For this feature to function properly, Option [2] Disarm with Access

Card must be disabled. If option [2] is enabled, access will be

granted and the partition(s) will be disarmed without entering the

user access code.

Option [8] ON = Access to armed doors is granted

Option [8] OFF = Access to armed doors is denied

13.7.8 Access Card Assignment

SECTIONS [801] TO [896]: ACCESS CARD SCREEN

The Access Card is activated by assigning its serial number to the

user access code. This system supports only the proximity cards

by Position Technology. Either enter the serial number manually or

present the Access Card to the reader and its serial number will

13.8 Multiple Action Feature

SECTION [504]: OPTION [1]

By enabling option [1] in section [504], users will remain in the

User Menu after entering their access code. This allows users to

perform more than one action without having to re-enter their

access code. With option [1] off in section [504], the control panel

will exit the User Menu after every action.

1 2 ... 39 40 41 42 43 44 45 46 47 48 49 ... 67 68

Kommentare zu diesen Handbüchern

Keine Kommentare

Digiplex DGP-641 Installationshandbuch Seite 44

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Digiplex DGP-641